RIS-enabled smart wireless environments: deployment scenarios, network architecture, bandwidth and area of influence

Reconfigurable intelligent surfaces (RISs) constitute the key enabler for programmable electromagnetic propagation environments and are lately being considered as a candidate physical-layer technology for the demanding connectivity, reliability, localisation, and sustainability requirements of next-generation wireless networks. In this paper, we first present the deployment scenarios for RIS-enabled smart wireless environments that have been recently designed within the ongoing European Union Horizon 2020 RISE-6G project, as well as a network architecture integrating RISs with existing standardised interfaces. We identify various RIS deployment strategies and sketch the core architectural requirements in terms of RIS control and signalling, depending on the RIS hardware architectures and respective capabilities. Furthermore, we introduce and discuss, with the aid of simulations and reflect array measurements, two novel metrics that emerge in the context of RIS-empowered wireless systems: the RIS bandwidth of influence and the RIS area of influence. Their extensive investigation corroborates the need for careful deployment and planning of the RIS technology in future wireless networks.

jointly optimised with conventional wireless transceivers [3,4] in order to significantly boost wireless communications in terms of coverage, spectral and energy efficiencies, reliability, and security, while satisfying regulated EM Field (EMF) emissions.
The most advanced RIS prototypes to date are built as antenna arrays operating in passive mode and including tunable unit cells and can be seen as either reflective or transmissive surfaces [5].Specifically, a reflective RIS operates as an EM mirror, where an incident wave is reflected towards the desired direction (typically anomalous, in the sense that this direction can diverge from the specular direction dictated by geometrical optics) with specific radiation and polarisation characteristics.On the other hand, a transmissive RIS operates as a lens or a frequency selective surface, where the incident field is manipulated (by filtering, polarisation change, beam splitting, etc.) and/or phaseshifted and re-radiated so as to control the refraction of impinging plane waves [6].It is noted that, when the RIS unit elements have both size and spacing lower than 1/10th of the communication operating wavelength, RISs are also termed as metasurfaces [7].Although RISs have great potential to implement advanced EM wave manipulations, mainly simple functionalities, such as electronic beam steering and multi-beam scattering, have been demonstrated in the literature, very recently, there has been increasing interest in the design of RIS hardware architectures [8], in response to the RIS potential for wireless networking and the resulting challenges.Those architectures endow surfaces with either minimal reception RF chains [9][10][11] or minimal power amplifiers [12], enabling more efficient channel parameters' estimation or extension of the RIS coverage area, respectively.Those capabilities can actually enable sensing, where RISs can act standalone or facilitate network-wide orchestration via minimal required control with the rest of the network [9], or establish relay-like amplification of the reflected signals in order to mitigate severe multiplicative path loss.
The RIS-enabled programmability of information-bearing wireless signal propagation has recently gave birth to the concept of the Wireless Environment as a Service [13], which was introduced within the European Union (EU) Horizon 2020 (H2020) RISE-6G project. 1 This environment offers dynamic radio wave control for trading off highthroughput communications, energy efficiency (EE), localisation accuracy, and secrecy guarantees over eavesdroppers, while accommodating specific regulations on spectrum usage and restrained EMF emissions.However, the scenarios under which RISs will offer substantial performance improvement over conventional network architectures have not been fully identified.In this article, 2 capitalising on the latest studies within the RISE-6G project, we try to fill this gap and present various deployment scenarios for RIS-enabled smart wireless environments, while discussing their core architectural requirements in terms of RIS control and signalling, depending on the RIS hardware architectures and their respective capabilities.We also introduce two key novel metrics that emerge in the context of RIS-enabled smart wireless environments: the bandwidth of influence (BoI) and the area of influence (AoI) of RISs, which corroborate the need for careful deployment and planning of the technology.

RIS deployment scenarios
In this section, we present general scenarios for connectivity and reliability with RISs, localisation and sensing applications with RISs, as well as RIS deployments scenarios for sustainability and secrecy.In most of the scenarios, we will distinguish between the consideration of RISs for boosting the performance of established wireless systems and for enabling wireless applications, which are otherwise infeasible.

Connectivity and reliability
Conventional network scenarios impose communication performance to be achieved via uncontrolled wireless propagation media, where the network is required to be tuned to one of the available service modes in a time orthogonal manner, offering nonfocused areas of harmonised and balanced performance.However, this might result in resource inefficiency and huge complexity.Conversely, the envisioned smart wireless environment, built upon RISs, will enable the granting of highly localised quality of experience and specific service types to the end users [13].In fact, such pioneering network paradigm aims at going one step beyond the classical fifth-generation (5G) use cases, by provisioning performance-boosted areas as dynamically designed regions that can be highly localised, offering customised high-resolution manipulation of radio wave propagation to meet selected performance indicators.Although we do not cover the details in this article, it is important to note that one of the central architectural elements of RIS-empowered wireless systems is the control channel [2].The rate and latency of this channel are crucial for the timely and efficient configuration of RIS-enabled smart wireless environments, and should be in accord with the overall system requirements.
For conventional system settings and strategies, based on a qualitative analysis of both localisation feasibility (including possibly high-level identifiability considerations) and expected performance, a system engineer needs to determine where and how RISs can improve connectivity.In all scenarios described in the sequel, we consider that RISs are in reflecting operating mode.It is noted, however, that a recent line of research [9][10][11] focuses on RISs that can also receive signals to, for instance, perform in-band channel estimation or localisation.This capability is expected to have an impact on the control channels for orchestrating smart wireless environments.Nevertheless, the deployments scenarios of sensing RIS will be similar to those of almost passive RISs, as long as the adoption of the former targets wave propagation control via RF sensing.Focusing on the downlink case, we next provide a taxonomy of RIS-empowered connectivity and reliability scenarios; the uplink case can be readily extended following analogous approach.

Connectivity and reliability boosted by a single RIS
In this scenario, there exist(s) direct communication link(s) between the multi-antenna base station (BS) and the single-or multi-antenna user equipments (UEs).However, connectivity can be further boosted efficiently via a single RIS, as shown in Fig. 1a.The phase configuration/profile of the RIS can be optimised via a dedicated controller, who interacts with the BS, for the desired connectivity and reliability levels.

Connectivity and reliability boosted by multiple individually controlled RISs
In this scenario, multiple BSs aim at boosting connectivity and reliability with their respective UEs.The deployed RISs are assigned to BS-UE pairs, and each pair is capable of controlling and optimising the phase profile of its assigned individual RIS(s), as illustrated in Fig. 1b.Since the action of an RIS can affect the propagation for links that are not intended to be controlled by that RIS, the result is that RIS operation interferes with the link operation.Unlike the usual wireless interference, which is additive, this can be seen as a multiplicative interference that needs to be handled carefully.Examples of interference management via a software-defined radio (SDR) setup with two RISs, targeting channel hardening of the received signals at UE terminals have been lately presented [15][16][17].The characterisation of the capacity limits in multi-RIS-empowered  wireless communications, and the practical schemes to achieve it, constitutes also an active area of research [18,19].

Connection reliability enabled by multiple RISs
In this scenario, the direct link(s) between the multi-antenna BS and the single-or multiantenna UE(s) is (are) blocked, and connectivity is feasible only via a single or multiple RISs, as shown in Fig. 2a.Similar to scenario 2.1.1,the phase profile(s) of the RIS(s) can be optimised for desired reliability levels, requiring, however, forms of coordination among the different BSs (e.g.possibly similar to the coordinated beamforming mechanism in LTE-Advanced [20]).

Connectivity and reliability boosted by a single multi-tenant RIS
For this scenario, we consider pairs of BS-UE(s) and a single RIS, as depicted in Fig. 2b.The RIS is now considered as a shared resource, dynamically controlled by the infrastructure and commonly accessed by the BS-UE(s) pairs.The phase profile of the RIS can be commonly optimised by the BSs to serve their own UE(s) simultaneously.Alternatively, the control of the RIS may be time-shared among the BS-UE(s) pairs.Of course, the control channel envisioned by this scenario will have to be thoroughly investigated in future activities.A special case of this scenario is the one which considers a setup where the communication is enabled by multiple cellular BSs, each one serving a distinct set of UEs.When the UE(s) move across the cell boundaries of two or more BSs, they might change their serving BS(s) frequently  resulting in frequent handover.Shared RISs among BSs can be placed in the cell boundaries in order to dynamically extend the coverage of the serving BSs, thereby reducing the number of handovers.

RIS-empowered multi-access edge computing
With the advent of beyond 5G networks, mobile communication systems are evolving from a pure communication framework to enablers of a plethora of new services, such as Internet of Things (IoT) and autonomous driving.These new services present very diverse requirements, and they generally involve massive data processing within low end-to-end delays.In this context, a key enabler is multi-access edge computing (MEC), whose aim is to move cloud functionalities (e.g.computing and storage resources) at the edge of the wireless network, to avoid the relatively long and highly variable delays necessary to reach centralised clouds.MEC-enabled networks allow UEs to offload computational tasks to nearby processing units or edge servers, typically placed close to the access points, to run the computation on the UEs' behalf.However, moving towards millimetre-wave and THz communications, poor channel conditions due to mobility, dynamics of the environment, and blocking events, might severely hinder the performance of MEC systems.In this context, a strong performance boost can be achieved with the advent of RISs, which enable programmability and adaptivity of the wireless propagation environment, by dynamically creating service boosted areas where EE, latency, and reliability can be traded to meet temporary and location-dependent requirements of MEC systems [21][22][23].Figure 3 depicts an RIS-enabled MEC system, where RISs are deployed to establish the wireless connections of two UEs with the edge server, via a BS which is backhaul connected with it.Fig. 3 An RIS-enabled multi-access edge computing system [23].At each time slot t, new offloading requests are generated by the UEs, which are handled by a dynamic queueing mechanism that accounts for communication and processing delays, and targets at jointly optimising communication and computation resources, while guaranteeing low-latency and high-accuracy requirements.τ denotes the time slot duration and f k (t) is the CPU frequency allocated by the edge server to UE k with k ∈ {1, 2} .R k (t) and R d k (t) stand for the uplink and downlink rates, respectively, while parameter J k depends on the application offloaded by device k.Q l k denotes the local queue update, Q c k is the computation queue at the edge server, and Q d k is the downlink communication queue

Localisation and sensing
The RIS technology is expected to enable advanced sensing and localisation techniques for environment mapping, motion detection, opportunistic channel sounding, and passive radar capabilities applied to industrial (e.g.smart factory), high user-density (e.g.train stations), and indoor (e.g.augmented/mixed reality) environments.The expected benefits can take various forms, depending on the RIS operating mode (i.e.reflect, refract, transmit, relay, etc. [8]), and they can be classified in terms of (i) enabled localisation (i.e.making localisation feasible where any conventional system [24,25] fails); (ii) boosted localisation (i.e.improving the localisation performance); and (iii) low-profile localisation (i.e.localisation requiring much lower resources in comparison with the conventional system).
In the following, ten generic scenarios where RISs provide performance benefits for localisation are presented (refer to the relevant open technical literature for a more comprehensive overview [26][27][28][29][30]).These scenarios are visualised in Fig. 4.
• Unambiguous localisation under favourable problem geometry with a minimal number of BSs: A single RIS enables localisation [26], while multi-RIS deployment settings [31] can also contribute to boost performance, by a combination of time and angle measurements.• Non-line-of-sight (NLoS) mitigation for better service coverage and continuity in farfield conditions: Whenever the minimum number of BSs (anchors) in visibility is not fulfilled, the UE location can be estimated via narrow-band signals received from two RISs.• NLoS mitigation for better service coverage and continuity in near-field conditions: Extending the previous scenario, the UE location can be estimated via the signal received from one RIS even without any BS in visibility, when the user is in the near-field of the RIS.This allows to exploit signal wavefront curvature for direct positioning [27,32].• On-demand multi-user and multi-accuracy service provision: The deployment (and the selective control) of multiple RISs makes possible (i) the (on-demand) provision of various classes of localisation services to different UEs sharing the same physical environment, depending on the needs they express locally/temporarily, while (ii) spatially controlling both the localisation accuracy and the geometric dilution of precision (GDoP) in different dimensions (i.e. both the sizes and orientations of the location uncertainty ellipses) [33].• Opportunistic detection/sensing of passive objects through multi-link radio activity monitoring: Similar to standard range-Doppler analysis [34], this is possible by monitoring the time evolution of multipath profiles over a communication link between the BS and one or several UEs, harnessing the dynamic and selective control of RISs [35][36][37][38].In highly reverberant environments, multiple RISs can create configurational diversity through wavefront shaping, even with single-antenna single-frequency measurements [5].• RIS-assisted search-and-rescue operations in emergency scenarios: RISs may support and overcome the shadowing effect induced by rubble in such scenarios by building ad-hoc controllable propagation conditions for the cellular signals employed in the measurement process [39].In addition, lightweight and low-complexity RISs mounted on drones can be used to bring connectivity capabilities to hard-to-reach locations, supporting first responders [40].• Localisation without BSs using a single or multiple RISs: In this scenario, wideband transmissions to a single passive RIS [41,42] or angle estimations obtained at multiple RISs [43,44], having the architecture of [11], can be combined to produce the estimation of UE(s) location(s).• RIS-aided radio environment mapping for fingerprinting localisation: RISs equipped with minimal reception circuitry for sensing [11] enable the cartography of the electromagnetic power spatial density in a specific area of interest, accentuating the location-dependent features of the RIS-enhanced radio signatures stored in the database.• Localisation with a RIS lens: In this scenario, the RIS is placed in front of a singleantenna transmitter.The user position is estimated at the UE side via the narrowband received signal, exploiting wavefront curvature [27].

• Indoor and outdoor localisation with simultaneously transmitting and reflecting RISs:
With the aid of a simultaneously transmitting and reflecting RISs [45], an outdoor BS is capable of localising an indoor user, in addition to an outdoor user via uplink sounding reference signals [46].
• Radar localisation/detection of passive target(s) with simultaneously sensing and reflecting RISs: Using the architecture of [9,10], a radar is assisted by multiple hybrid RISs in order to localise/detect both static or moving target(s) [47], extending scenario 5. Hybrid RISs can simultaneously sense (via dedicated reception RF chains or other signal sensing elements) and reflect providing the system with the capability to localise UEs as well as the radar itself.They can also be deployed for joint channel and direction estimation for ground-to-drone wireless communications [48].

Sustainability and secrecy
RIS-empowered smart radio environments are expected to improve the sustainability and security of 6G networks by focusing the energy towards the target UE, thus reducing the amount of unnecessary radiations in non-intended directions in general, or in the directions of non-intended UEs (e.g.exposed UEs or eavesdroppers).More precisely, the following metrics can be improved: (i) the EE [3] (for instance, this metric can be defined as the attained data rate at the target UE divided by the BS transmit power); (iia) the self-EMF exposure utility (S-EMFEU) (for instance, in uplink, this metric can be defined as the attained data rate of the target UE divided by its exposure to its own UE emissions, (ii-b) the inter-EMFEU (I-EMFEU) (for instance, this metric can be defined as the attained data rate at the target UE divided by the largest EMFE at another UE); and (iii) the secrecy spectral efficiency (SSE) [49,50] (for instance, this metric can be defined as the attained data rate at the target UE minus the data rate that is intercepted by the eavesdropper).A first already identified use case for such improvements [13] is a train station, where an orchestrated network of RISs can be optimally configured to maximise the aforementioned metrics, in small areas close to the surfaces.These areas can be advertised to customers as "areas with high EE, " "areas with low EMF exposure, " or "areas with increased secrecy." In contrast to conventional network deployment scenarios that lack RISs, Fig. 5 illustrates single-BS scenarios with one or more RISs, where downlink zero-forcing transmit Beam Forming (BF) is used from the BS to boost the received signal power at an intended UE as well as to reduce the received power at an non-intended UE; Fig. 5 The three core scenarios for RIS-empowered sustainability and secrecy discussed in Sect.2.3.In all scenarios, thanks to the RIS(s), UE 2 eavesdrops less (or is less exposed by) UE 1 downlink data because UE 2 is now on a location where propagation has been weakened artificially this operation can be achieved by exploiting the artificial shaping of the propagation channels offered by the reconfigurability feature of the RIS(s).When the non-intended UE is an exposed user, the obtained link is a low EMF link, whereas when the nonintended UE is an eavesdropper, the obtained link is a secured link.The figure shows, for three propagation scenarios, the advantages brought by an RIS(s) and zero-forcing BF in terms of reducing the received signal power at the non-intended UE (whether it is an eavesdropper or an exposed user), as compared to the received power at the target UE.
1 The BS-to-intended-UE link is in LOS: In this case (left figure), the RIS artificially adds propagation paths to the channel, which coherently combine with other "natural" paths to boost the received power at the target UE, and non-coherently combine with other "physical" paths to reduce the received power at the non-intended UE. 2The BS-to-intended-UE link is blocked by an obstacle and the intended UE is in the near-field of an RIS: In this case (middle figure), the RIS artificially adds a propagation path to the existing "physical" paths to reduce the received power at the non-intended UE; 3 The BS-to-intended-UE link is blocked by an obstacle and the intended UE is in the far-field of an RIS: This case (right figure) is similar to the previous case except that several RISs may become useful to reduce the energy at the non-intended UE.
In the absence of a non-intended UE, it is noted that the proposed system in Fig. 5 only boosts the received power at the target UE, and therefore, boosts the EE metric.Note also that similar scenarios for uplink can be derived with receive BF instead of transmit BF.Regarding EE, the main difference will be that the EE will be improved at the UE side.
Regarding the EMF utility, the main difference will be that the target UE and the exposed UE will be the same entity, instead of being distinct entities.In this case, the RISs will help reducing the self-exposure of a UE transmitting data in the uplink with its own device.Furthermore, the previously described scenarios can be generalised to multi-BS scenarios, where several synchronised and coordinated BSs perform joint BF [20].

RIS integration in standardised networks
The deployment of wireless networks takes under consideration the following two basic principles of radio transmitters: a transmitter emits information-bearing signals in a limited spectrum bandwidth over a limited coverage area, depending on its hardware/ software capabilities and various operation regulation factors.In addition, a wireless network operator ensures that the interference among its own BSs is minimal, by carefully planning their deployment and orchestrating their operation.More specifically, operators spatially distribute their BSs and access points to avoid overlaps among their limited coverage areas.Spectrum regulation ensures that interference among different network operators (with possibly overlapping coverage) is avoided, by allocating separate and limited spectrum bands, as well as defining spectrum masks and maximum out-ofband emission thresholds.Very recently, RISs have been introduced as a new type of network node.A reflective RIS does not emit any signal, instead, it re-radiates the EM waves impinging on its panel [51].As a result, such an RIS has no explicit coverage area nor explicit transmit bandwidth.In fact, the former will be determined by both the RIS capabilities, primarily its fabricated reflective features, and the sources whose radiated waves impinge on the RIS.This area around the RIS, which is expected to be much smaller than that of a BS or an access point, is defined as its AoI.As previously mentioned, the notion of the transmit bandwidth is not relevant for a reflective RIS.However, it will impact the reflections of the signals impinging on it, which will usually span a certain range of frequencies.The amount of the RIS influence on those signals will depend on the RIS frequency-related characteristics, which again primarily depend on its fabricated reflective features.The range of frequencies that an RIS can impact is defined as its BoI.Putting all above together, RISs cannot be trivially integrated neither in network planning nor spectrum regulation as usual BSs or other network devices.In this section, we elaborate upon the two new concepts of RIS AoI and BoI and their key roles in the deployment of RIS technology in future wireless networks.

Network architecture
In Fig. 6, we present a simple integration scheme for RISs in 3GPP networks.As illustrated, the gNB communicates with a UE via the assistance of two reflective RISs, which cannot receive or emit any data (in the sense that they do not have such capability hardware-wise); extensions to RISs including active elements for reception and/or transmission are left for future investigations [8].Each RIS is assumed to only influence the quality of the data link between the UE and gNB, acting as a costefficient passive relay between those nodes.An RIS node comprises, apart from the reconfigurable reflection panel, a small and low-power signalling module, compactly known as the RIS controller, that is equipped with circuitry for managing the RIS phase configuration as well as transceiver radios to communicate with the gNB and UE, thus, enabling the RIS communication and interface with the rest of the network.In more detail, the RIS controller is responsible for generating the logical commands associated to the switching operations between the configurations/states of the RIS elements (e.g.predefined phase shifts), and can have different levels of complexity and capabilities, possibly embedding third-party applications to implement smart algorithms (e.g. the direction estimation of the impinging signals [43]).The RIS controller may either accept requests from other elements in the network; in this case, it will simply act as an interface that configures the RIS elements based on external explicit instructions (this is an externally controlled RIS), or it may operate on its own (this is an autonomous RIS [9] that can perform self-optimisation according to its own intention or as a response to a reflection-optimisation request by an external cooperating node; the request can be realised with minimal interaction between that node and the RIS controller).The expected action time granularity for the operations of an RIS controller is envisioned to be between 20 and 100 ms.
As depicted in Fig. 6, the gNB and UE communicate with each RIS over the air through new radio interfaces and radio channels to be specified and embedded in the future new radio (NR) standards.To this end, one can identify up to 8 different types of L1/2 in-band signalling in this example integration figure: It is noted that, with the proposed integration scheme and novel radio interfaces, many different types of basic RIS control can be implemented.In the following, we describe a representative example aiming the joint optimisation of the BS transmit BF and the RIS reflective BF (i.e.RIS phase configuration/profile).
Assume the time division duplex (TDD) mode and uplink-downlink channel reciprocity.In addition, the scheduler of the physical (PHY) and medium access control (MAC) layers considers the gNB as the master node for the two reflective RIS nodes, using C1 and P1 L1/2 signalling to control them.The steps for the intended joint BS/RIS BF optimisation can be summarised as follows: -Step 1: The gNB sends requests to the RISs through C1 to switch between predefined reflective beams during a predefined sounding phase.-Step 2: During the sounding phase, the two RISs switch in an ordered and synchronised manner (thanks to synchronisation signals over P1); the UE sends uplink pilots; and the gNB sounds the uplink channel for each reflective beam realised by the RISs.-Step 3: The gNB determines the jointly optimised transmit BF weights as well as the reflective BF configuration from the RISs.-Step 4: The gNB notifies through C1 the RISs to configure themselves according to the decided reflective BF configurations in the previous step.
- Step 5: During the data transmission phase, the gNB transmits data using the best transmit BF weights.This data is received by the UE through a two-RISsparameterised signal propagation channel that is subject to the desired influence of the two involved RISs.
Similarly, to allow control of any of the RISs by the UE, at least C2 and P2 signalling are necessary.C3 and C4 control signals could be also added to enable the RIS (actually, its controller) to answer requests from the UE and/or the gNB, and send acknowledgment or negative acknowledgment.The pilots signals P1 to P4 can be sent/received from/by each RIS controller.Hence, they cannot be used to sound the channel between the unit cells of each RIS and the gNB or UE.However, those pilots are necessary to estimate the propagation channel used by the L1 control signalling, facilitating its equalisation, and consequently, signal demodulation.The right part of Fig. 7 illustrates the main functional blocks of existing network architectures, including Open RAN (O-RAN) and the RAN functional split according to 3GPP [52].All 3GPP-compliant interfaces are coloured in blue, whereas the O-RAN interfaces are red-coloured.In the figure, we split the RAN elements, namely eNB or gNB according to the 3GPP jargon, specifically, into a centralised unit (CU), a distributed unit (DU), and a remote unit (RU).While DU functions can be placed on an edge cloud, they would require a very high capacity connection links to assist and support real-time operations between the radio link control (RLC)/MAC layers and PHY.Additionally, the CU functions can be placed on edge clouds; in this case, they shall be split into control plane (CP) and user plane (UP) functions.DUs are connected to RUs by means of the Open FrontHaul (O-FH) protocol.Following the O-RAN architecture perspective, the figure depicts the near-real-time (near-RT) RAN intelligent controller (RIC) that automatically interacts with the CU functions through the indicated standardised E2 interface.This RAN controller can automatically integrate third-party applications, namely xApps, which control specific RAN functions.Also, the non-real-time (non-RT) RIC can exchange messages with the near-RT RIC using the standardised A1 interface.According to our proposed Fig. 7 The proposed network architecture integrating RISs with existing standardised interfaces, such as 3GPP, O-RAN, and ETSI RIS-enabled smart wireless environment architecture in Fig. 7, the aforementioned conventional network architecture blocks can interact with new RIS-oriented network entities (i.e. the left part of the figure) via the novel interfaces represented by F1-x, R2, and Ro.Two representative use cases can be envisioned by means of the latter interfaces: • The RIS is directly connected to enB/gnB enabling BS transmit and RIS reflective BF to be jointly optimised, i.e. the network operator owns the RIS deployment.In this case, the CU control plane can trigger specific phase configuration at the RIS via its actuator within few milliseconds.It is noted that the RIS actuator will be responsible for actuating the logical commands received by the RIS controller, i.e. for translating them into physical configurations to be applied to the RIS panel.This direct connection of the RIS to the enB/gnB is particularly relevant when the RIS deployment is under the network operator control.• The RIS is connected to the management of the eNB/gNB in a master/slave or peer-to-peer fashion.In this case, the RIS actuator and the RIS panel can only be configured by the RIS controller.However, the latter interacts with the near-RT RIC by means of a dedicated xApp that will have its counterpart in the RIS controller.This case includes self-contained and independent RIS deployments, which can be dynamically integrated into the network and used by operators upon request.
This open environment implementing RIS-enabled smart wireless networking is envisioned as a class of new protocols that can be optimised to include different types of RISs (e.g.reflective, transmissive, and simultaneous reflecting and sensing [8]).

The RIS bandwidth of influence (BoI) challenge
Consider a wall or any "dumb surface" in the signal propagation environment of a wireless network.The reflection properties of this wall depend on its material and the network's operating frequency f, as well as on the impinging angles of its incoming signals.In general, signal reflections from the wall follow Snell's law [53] (i.e.geometrical optics) and cannot be dynamically configured.In contrast, each unit cell of a reflective RIS has a reconfigurable reflection and/or transmissive capability, appearing in a limited range of frequencies of the impinging wave.This range of frequencies that an RIS can impact signal propagation (i.e.reflection/transmission) is defined as its BoI.In fact, an RIS is composed of a set of usually identical unit cells (called also as unit elements or meta-atoms), and its overall influence over wireless communications cannot exceed that of its single unit cell, which is limited in the frequency domain.Therefore, studying the BoI of a unit cell in a uniform RIS is sufficient to characterise this metric for the entire RIS.This will be the focus in the following.
As illustrated in Fig. 8a, when the unit cell of an RIS, which is configured in a state x, gets illuminated by an impinging wave with unit power and frequency f, it reflects this wave with a complex reflection coefficient S11(f, x) and also transmits another wave with a complex transmission coefficient S21(f, x) .For a given frequency f, these S-parameters depend on the state x of the unit cell.Let us define C R (f ) and C T (f ) as the maximum contrasts among all states of the unit cell in terms of reflection and transmission, respectively.Following these definitions, C R (f ) and C T (f ) can be mathematically expressed for any feasible unit cell state x, and a feasible unit cell state x ′ � = x , as follows: where | • | denotes the amplitude of a complex number, and it holds that 0 ≤ |C R (f )| ≤ 2 and 0 ≤ |C T (f )| ≤ 2 since the S-parameters are bounded by 1.It is noted that, when the maximum contrast values are both close to zero, the unit cell behaves like a "dumb point" (e.g. a point of a "dumb surface"), i.e. a non-reconfigurable one.In this case, its S-parameters only depend on f and the unit cell has no capability to change state, i.e. its state is fixed depending on its material and on its placement with respect to the impinging wave.
Let us define a threshold C min beyond which the maximum contrast C R (f ) , or C T (f ) , of a reflective RIS is considered as significant, and consequently, its unit cell can be considered as having a more significant dynamically adjustable influence on the wave that it re-radiates at frequency f (due to an impinging wave at this frequency).As the contrast is lower bounded by 0 and upper bounded by 2, in the sequel, we chose C min equal to 1.The BoI of an RIS is defined as the range of frequencies for which the contrast is more significant for both its incoming (i.e.impinging) and outgoing (i.e.reflected or re-transmitted) wave.For instance, the unit cell of an efficient reflective RIS will have a more significant dynamically adjustable influence on the wave reflection inside its BoI, and a weaker influence on the reflection happening outside of it.Using the latter definitions and notations, the BoI of the unit cell of a reflective RIS can be mathematically expressed as follows (see Fig. 8b for an illustrative interpretation): where it should also hold that C R (f ) ≫ C T (f ) .In Sect. 4 that follows, characterisations of contrasts and BoIs for various implementations of unit cells for one transmissive and three reflective RISs will be presented.For those investigations, we further introduce the RIS central frequency f 0 .By representing the BoI as the frequency set [f 1 , f 2 ] , f 0 is defined as follows: Note that alternative f 0 definitions could be used, e.g.

The RIS area of influence (AoI) challenge
As illustrated in Fig. 9, the RIS can be configured to contribute an additional signal propagation path to the available paths between a BS and a UE.In this way, it can influence the existing coverage between those two nodes.Specifically, the RIS can either improve/extend the coverage, in terms of a Quality of Service (QoS) metric, or degrade it, depending on its phase profile setting.The geographical area where the coverage of a Fig. 9 Illustrative description of the AoI of an RIS.The RIS may either improve or degrade the QoS in certain geographical areas, leading to desired or undesired AoI, respectively BS for a given service with a given target QoS can be modified via an RIS is defined as the AoI of the RIS.In particular, the area where the service coverage of the BS is improved, or extended, is the desired AoI, whereas the area where it is degraded is the undesired AoI.In mathematical terms, the AoI of an RIS of any type can be defined as follows: where m(•) represents the desired performance metric evaluated over a geographical area A under investigation and q th is the minimum service requirement.Note that it must hold: S ⊆ A.
Neither the shape nor the location of the AoI of an RIS is intuitive, and both depend, among other factors (such as the environmental conditions and the settings of several network parameters, e.g.RIS's location and orientation as well as BS's transmit power level), on the considered performance metric.In practice, a planning tool based on ray tracing is necessary to visualise the AoI [54] and to contribute in choosing the best locations for deploying RISs [55].In Sect. 5 that follows, characterisations of AoIs for various types of RIS-boosted services will be discussed.

Operators coexistence with RISs
Figure 10 illustrates the case where two network operators O1 and O2 possess different spectrum bands and each deploys a separate BS.It is assumed that operator O2 also deploys a reflective RIS.In Fig. 10a, the BoI of the RIS is depicted as ideal, meaning that it perfectly matches the spectrum owned by O2, influencing solely its coverage, and not that of operator O1.However, in Fig. 10b, the non-ideal case where the BoI of the RIS of O2 overlaps with the spectrum owned by O1 is considered.In this subfigure, we further assume that the RIS has an AoI that overlaps with the geographical coverage of O2.This implies that a UE served by operator O1 and located in the RIS's AoI will suffer from undesired reflections from the RIS.Those reflections are AoI {S | m(S) ≥ q th }, Fig. 10 The operators' coexistence challenge when an RIS is deployed undesired, in the sense that, they fluctuate in a discontinuous and unpredictable manner for the service provided by O1.Such fluctuations may degrade the performance of closed-loop link adaptation mechanisms (such as adaptive modulation and coding, power control, and adaptive BF) as well as of fast scheduling schemes, degrading the overall link performance.
The non-ideal RIS deployment case in Fig. 10b is investigated in more detail via the example illustrated in Fig. 11.As shown in Fig. 11a, a UE connected to the operator O1 acquires and reports the channel state information (CSI) at time instant t, which is represented as CSI(t).At time instant t + dt , as depicted in Fig. 11b, the UE receives data from O1 with a link adaptation based on CSI(t).However, due to the existence of an RIS operated by O1, which changed from phase configuration 1 to 2 between instants t to t + dt , respectively, the channel between the BS of O1 and the UE changed.Fig- ure 11c demonstrates that this RIS phase configuration change may suddenly degrade the received signal-to-noise ratio (SNR) at the UE.This actually indicates a mismatch between the SNR prediction (based on the CSI(t) value) used for link adaptation, and the actual SNR at time t.As depicted in Fig. 11d, this translates into a large block error probability (BLEP) resulting in an erroneous packet reception.To conclude, showcased that an RIS by a network operator, and having a BoI overlapping the spectrum of another operator, can degrade the QoS of the latter.This fact witnesses the importance of the BoI characterisation of RIS equipment in driving their efficient design and fabrication in order to ensure smooth coexistence among operators that deploy RISs.

Bandwidth-of-influence experimental characterisation
In this section, we present novel experimental results for the BoI of the various fabricated RISs in the framework of the ongoing RISE-6G project.In particular, we characterise the BoI of the following RIS unit cell implementations: • Unit cell of an 1-bit transmissive RIS (T-RIS) [56][57][58]; • Unit cell of a varactor-based reflective RIS (R-RIS) [59][60][61]; • Unit cell of a RF-switch-based R-RIS [62]; and • Unit cell of a PIN-diode-based R-RIS.
For each implementation, the characterisation includes: (i) the maximum contrast (defined in Sec.3.2) as a function of the frequency f; (ii) the BoIs at the value C min = 1 , which serves as the contrast threshold; and (iii) the central operating frequency f 0 of the RIS structure.

BoI of an 1-bit PIN-diode-based transmissive RIS
Figure 12a, b depict the structure of the unit cell of an 1-bit T-RIS, which is an improved version of the unit cell firstly introduced in [56,57].This improved unit cell has the following characteristics [58]: (i) it is designed to operate at frequencies lying approximately between 23 GHz and 32 GHz, and (ii) it is composed of the four metal layers: receiving patches; transmitting patches; biasing lines (transmission sides); and ground plane.This T-RIS is illuminated by a source from the receiving patch side.On the transmitting patch, the alternation of the diodes state produces a 180 • phase difference.The unit cell ensures an 1-bit phase quantisation for transmission.Figure 12c-e illustrates the magnitude, the phase, and the contrast (which is the difference between the two possible states of the unit cell) of the S-parameters as functions of the frequency f in GHz, as obtained by the Ansys HFSS full-wave EM simulator under periodic boundary conditions.For this 1-bit unit cell, the contrast in terms of the reflection C R (f ) and transmission C T (f ) are computed as follows: In Fig. 12e, the contrasts of the S11 and S21 parameters are demonstrated versus different frequency values.As expected in this case (recall that this implementation is a T-RIS), C T (f ) is much larger than C R (f ) , hence, we use C T (f ) to determine the BoI (see Sec. 3.2 for the justification).It can be seen that the BoI at the maximum contrast threshold C min = 1 is [23.9, 30.6]GHz, resulting in a width of 6.7 GHz with a central frequency f 0 equal to 27.3 GHz.

BoI a varactor-based reflective RIS
we characterise the unit cell of a varactor-based R-RIS with continuous phase shifting [59][60][61].As illustrated in Fig. 13a, this unit cell is loaded with a variable capacitance, whose values range from 0.1 to 0.9 pF, which is voltage-controlled continuously via diode varactors [63].Hence, the S11 parameter accepts continuous values and its magnitude and phase, as functions of the frequency f in GHz, are illustrated in Fig. 13b, c, respectively, considering 9 different values of the capacitance between 0.1 and 0.9 pF with 0.1 pF step.Figure 13d includes the maximum contrast C R (f ) , which was obtained for each possible pair of capacitance values.It can be observed that the BoI at the contrast threshold C min = 1 is approximately [5.1, 6.4] GHz, having a width of 1.3 GHz.In this case, the central frequency f 0 is equal to 5.8 GHz.

BoI of an RF-switch-based reflective RIS
In this subsection, we evaluate the BoI of the unit cell of the RF-switch-based R-RIS in [62], which is depicted in Fig. 14a.This unit cell was designed to operate at 5.3 GHz and consists of a patch antenna connected to an RF switch, which is in turn connected to 8 different outputs: 7 of these outputs are attached to open-ended delay lines of different lengths, while 1 of them is attached absorber, which allows to effectively turn off the length of each delay line is designed to impose 7 different phase shifts to the impinging signal at the unit cell; those phase shifts are equally spaced in the range from 0 to 2π.
The magnitude of the S11 parameter represents the portion of the energy of the impinging signal that is immediately reflected back at the interface with the patch antenna.Hence, in order to compute the BoI, we first define the following variable: which represents the portion of the energy of the impinging signal that enters the patch antenna, gets re-directed to one of the delay lines of the unit cell, and finally gets reflected back in the air.We, thus, define the unit cell "effective S11 " as follows: where ∠S11 represents the argument of the complex number S11 .Finally, for every frequency value f, we compute the maximum contrast in the effective S11 as: where c i and c j represent any two distinct RIS unit cell configurations.
The magnitude and phase of the S11 parameter, as obtained from full-wave simulations, are shown in Fig. 14b, c, respectively.It is depicted that the magnitude of S11 exhibits a strong positive peak at the working frequency of 5.3 GHz, meaning that most of the incoming signal's energy is reflected back by the unit cell's patch antenna.Moreover, at this frequency, the phase of S11 attains 7 equally spaced values in the range from 0 to 2π .Note that, in this case, the BoI never goes to zero since, even outside the operating frequency range, a (small) portion of the impinging signal always enters the unit cell and gets reflected through a different delay line, depending on the chosen configuration.It is noted that this effect can be mitigated by tweaking the design parameters of the unit cell (e.g. its dimensions).Finally, Fig. 14d demonstrates the BoI at the contrast threshold C min = 1 which is [5.17, 5.44] GHz, yielding a width of 270 MHz.The central frequency f 0 for this R-RIS fabricated structure is 5.3 GHz.

BoI of an 1-bit PIN-diode-based reflective RIS
Hereinafter, we evaluate the BoI of the unit cell of an 1-bit PIN-diode-based R-RIS operating in the sub-6 GHz frequency band.The schematic view of this cell as well as the active elements values corresponding to its two possible states is illustrated in Fig. 15a.The designed dual linearly polarised unit cell operates at the central frequency 5.2 GHz.It is composed of one metal layer consisting of two orthogonal folded dipoles and a matching network circuit printed on a thin 0.1 mm FR4 substrate.This substrate, characterised by ǫ r = 4.3 and tan(δ) = 0.01 , is placed upon a thick 3 mm LERD spacer (with ǫ r = 1.04 and tan(δ) = 0.0001 ) and is backed by a metallic 1 mm ground plane realised with an aluminium reflector.At the top layer, two radiating elements are present, which are placed normal to each other to cope two orthogonal polarisations.Two PIN diodes are connected to the inner printed matching network and are biased in opposite states; one diode is switched ON, while the other one is in OFF state.
By operating in this binary mode, it is possible to obtain a reflection coefficient phases of 0 • or 180 • degrees, depending on the polarisation state of the diodes.This 1-bit unit cell has been simulated for its two-phase states using the commercial software Ansys HFSS with periodic boundary conditions on the cell's lateral faces and Floquet port.As shown in Fig. 15c, the unit cell exhibits a phase difference of almost 180 • over the whole considered frequency band for both states.The unit cell's magnitude is depicted in Fig. 15b for both the 0 • and 180 • states.The contrast in terms of the S11 parameter is plotted as a function of the frequency f in GHz in Fig. 15d.As it can be observed, the BoI at the contrast threshold C min = 1 is approximately [4.4, 5.6] GHz with a width of 1.2 GHz.In this case, the central frequency f 0 is defined as the mid-frequency of the BoI and is equal to 5.05 GHz.

BoI comparison among different RIS implementations
In Fig. 16, we the at contrast threshold C min for four aforede- scribed fabricated RIS unit cells.In particular, the maximum as a function of the normalised frequency divided by the depends its physical electrical size, as as its Hence, its in terms of versus frequency, on implementation of the reconfiguration mechanism.It can be observed, for the unit cell of the PIN-diode-based R-RIS, that the maximum contrast is quite flat within its BoI, while dropping abruptly outside of it.This is due to the fact that, when the unit cell is on the ON state, it has a slightly larger physical size; hence, it strongly resonates in the lower part of the BoI, but still significantly resonates in its upper part.However, when the unit cell is on the OFF state, it has a slightly smaller physical size, but it again strongly resonates in both the upper and lower parts of the BoI.This implies that the BoI's lower and higher frequencies are close enough, yielding a nearly flat maximum contrast.A similar contrast behaviour appears to the unit cell of the PIN-diode-based T-RIS.In this case, however, the lower part of the BoI is mainly due to the patch's size (which slightly increases), whereas BoI's upper part is mainly due to the slot size in the patch (which slightly decreases).In this RIS unit cell design, the reconfiguration only changes the orientation of the current circulating on the patch.
Regarding the maximum contrast behaviour for the unit cells of the RF-switch-based and varactor-based R-RISs, it is reminded that the former's states result from changes on the length of the cell's feeding line, whereas the latter offsets, in the frequency domain in a continuous manner, its peak resonant frequency linked to its electrical size.To this end, in the former case, the BoI depends on the resonant frequency of the patch antenna's physical size (recall that this antenna resonates in a narrow band), whereas, in the latter case, the contrast behaviour over frequency is mainly limited by the cell's physical size.
In conclusion, different hardware designs and fabrication approaches of RIS unit cells yield different BoIs, which should be carefully considered when deploying RISs in wireless networks, as discussed in Sec.3.4.Evidently, an RIS with a large BoI is not always the best option.In fact, the RIS hardware design, in terms of its BoI, needs to be optimised according to the intended deployment scenario and use case.

Area-of-influence experimental characterisation
In this section, we investigate the desired AoI of a reflective RIS for several use cases referring to different QoS requirements.In particular: • Boosting a UE's EE using an RIS; in this use case, the self-exposure of the UE to its own emissions is also reduced.This implies that this use case can be also considered as an S-EMFEU boosting use case.• RIS-enabled localisation boosting.

Example of an EE-/S-EMFEU-Optimised AoI
We first focus on the use case EE/EMFEU and enabling.More precisely, consider scenario where a UE transmits information to an outdoor massive Multiple-Input Multiple-Output (MIMO) BS (i.e. in inside or outside a outside a with two a "north with two windows and "south room" with only one north door.The massive MIMO BS was located outside north.To characterise the influence of the RIS deployment, we have compared two scenarios: one without the RIS and another one with the RIS placed in the north room upon the south wall. Let us first visualise how the RIS improves the propagation between the UE and the BS. Figure 17b illustrates three heatmaps of the equivalent channel gain between the UE (for all positions of the UE upon the map) and the BS, taking into account the BS's reception BF: • The heatmap of the channel gain in the absence of the RIS; As depicted figure, the RIS, the channel is particularly strong close to the two windows of the north room, and the south room, except intentionally positioned on the south room, on a location which benefits from a strong channel, thanks to one of the north windows.The RIS mainly improves the gain in the south room, by creating propagation paths between the south room and the BS.
We next visualise how the improvements in channel gain, illustrated in Fig. 17b, translate into improvements for a given performance metric, such as the EE from the UE perspective.We now consider the use case where the UE wishes to transmit voice data to the BS. Figure 18a illustrates three heatmaps of the UE transmit power adapted to the propagation channel to provide voice service, with a target receive SNR at the BS: (i) the UE transmit power in absence of the RIS; (ii) the UE transmits Fig. 18 EE-/S-EMFEU-optimised AoI, where three types of influences are illustrated: the "unchanged" (blue region), the "boosted" (green region), and the "enabled" areas (yellow region) showcasing the spatial distribution for the EE/S-EMFEU metric in the presence of the RIS whose reflective BF is jointly optimised with the BS receive BF; and (iii) the UE transmit power reduction (i.e.EE improvement) due to the introduction of an RIS.It is demonstrated that, when the propagation environment is poor, the voice QoS cannot be attained with power.This implies that the not transmit any data it is out of coverage.Figure 18b types of areas: (i) where no change due to the RIS is observed (the UE remains out of coverage or keeps reaching the maximum data rate enabled by the standard with the minimum transmit power enabled by the device); (ii) the "boosted area" where the UE transmit power is reduced and the EE is boosted; and (iii) the "enabled area" where the UE gets voice coverage thanks to the RIS.The EE-optimised AoI is the combination of the "boosted area" and the "enabled area".It is noted that the EMFE of the UE to its own emissions is also Fig. 19 The RIS-enabled AoI optimisation for the uplink SE metric for the case where the UE is transmitting using its maximum available power reduced when its transmit power is reduced.Therefore, the S-EMFEU-boosted area is the same as the EE-boosted area, and the same holds for the S-EMFEU and EE AoIs.

Example of an uplink SE-optimised AoI
In this section, we visualise how the improvements in channel gain illustrated in Fig. 17 do translate into improvements for the SE performance metric, expressed in bits/sec/Hz.We consider a use case where the UE transmits voice service plus best effort data traffic using its maximum transmit power.Figure 19a illustrates the uplink spectral efficiency (SE) when the UE transmits with maximum power and adapts the data rate (thanks to adaptive modulation and coding) to the propagation channel, with the aim to maximise the best effort service data rate (in addition to the voice service).Three heatmaps are plotted in Fig. 19b: (i) the SE without the reflective RIS; (ii) the SE in the presence of the RIS with jointly optimised BS receive BF and RIS reflective BF; and (iii) the SE improvement due to the introduction of RIS.It is shown that, when the propagation conditions are weak to offer the minimum performance (i.e. the voice service alone), the UE does not transmit at all being out of coverage.
Similar to Sect.5.1, three types of areas are depicted in Fig. 19b: (i) the "unchanged area" where no change due to the RIS deployment and optimisation is observed (the UE remains out of coverage or keeps reaching the maximum data rate enabled by the standard with the minimum transmit power enabled by the device); (ii) the "boosted area" where the SE is boosted; and (iii) the "enabled area" where the UE gets voice (and potentially data) coverage thanks to the RIS.The SE-optimised AoI is the combination of the "boosted area" and the "enabled area".

Example of a localisation-optimised AoI
In Fig. 20, we deploy three single-antenna BSs (red triangles) at the points [0.5, 1] ⊤ , [4.8, 4.8] ⊤ , and [1, 4.8] ⊤ in metres and a single-antenna UE to perform downlink mul- ticarrier 2D localisation depending on three direct paths.A uniform linear array (ULA) RIS in reflective mode (green star) deployed at the point [4, 0] ⊤ in metres is installed to investigate its effect on the positioning performance.In our evaluation scenario, the RIS is assumed to be activated and controlled to produce one reflected path in the geometric near-field (NF) regime, in addition to the LoS direct path.This is achieved by exploiting the wave front curvature [32] and occurs exclusively when the BS closest to the RIS (located at [0.5, 1] ⊤ ) is transmitting.The remaining two BSs are considered to contribute only with direct paths to the system.Moreover, the end-to-end RIS precoder is randomised, but yet constrained to a predefined lookup table of realistic hardware RIS element-wise complex reflection coefficient measurements (the set K2 in [64] with 2-bit phase control and corresponding phases 0, π/2, π, −π/2 ; another option could be the prototype in [59]), and a directional beam pattern is thus approximated.However, the RIS performance can be further improved by adopting a location-optimal phase design as in [65] instead of randomly drawing from the predefined lookup table.As for the simulation parameters, the BSs were considered to transmit 40 pilots in a wireless environment with free-space path loss.The operating frequency was 28 GHz and the bandwidth was assumed sufficiently large with 256 subcarriers and a 240 KHz bandwidth per subcarrier.The simulation area was 5 × 5 square metres and the UE's position was assumed known at each point where the Fisher Information Matrix (FIM) was computed, after which the Cramer-Rao lower bound (CRLB) on each position estimation as derived in both scenarios (with and without the RIS).
Figure 20a provides heatmaps of the resulting Position Error Bound (PEB) without and with RIS, as well as the difference between these two cases.Figure 20b then shows, in three colours, the different effects of deploying a reflective RIS for localisation purposes in the aforementioned scenario.First, the localisation is said to be "infeasible" in the Fig. Localisation AoI, showcasing the impact-in terms of the PEB (in dB)-of a reflective RIS deployed close to the lower right corner of the investigated scene (green star) to assist a conventional downlink positioning system relying on 3 BSs (red triangles).Interestingly, the RIS enables localisation and, even significantly boosts, accuracy in subregions close to the RIS (resp.yellow and green areas), without degrading performance elsewhere (blue area) conventional (three BSs only) system, if the expected accuracy is arbitrarily worse than 0.1 m (according to some a priori application requirements).Accordingly, the first area, in yellow, is called "enabled" by the RIS, if the target accuracy is then met (in the same region).We can observe this effect, more particularly, in the area closest to the RIS, a.k.a in the AoI, where positioning is not just enabled, but actually enhanced up to a considerable level.We also see this effect behind the BSs, where a poor GDoP would deprive the conventional system from properly inferring the UE location.The second effect that we notice, in blue, is labelled as "unchanged." This is where the three BSs already achieve rather a good localisation performance, while the RIS does not have a noticeable improvement (less than 2 dB).This is mostly visible in the inner region between the three BSs.Lastly, we notice a "boosting" effect in the green region, which is also known in the literature as a "RIS-boosted localisation" regime.Accordingly, while the conventional system relying uniquely on the three BSs can achieve acceptable performance, the RIS further contributes in improving localisation to a significant extent, which leads to PEB level improvement by 3 dB or more.

Example of an SSE-optimised AoI
In this section, we consider a scenario including a legitimate communication pair, comprising a BS and an RX, as well as an eavesdropper Eve, with all nodes equipped with multiple antennas and placed in the same geographical area.
In Fig. 21a, we plot three different heatmaps of the SSE (which is defined as the data rate attained at the target UE minus the data rate that is intercepted by Eve [49, eq.Sec.II]): (i) when there is no RIS deployed; (ii) when there exists an RIS optimised for SSE maximisation; and (iii) the difference in SSE performance due to the introduction of the RIS.More precisely, each heatmap is obtained assuming that the BS's, Eve's and RIS's positions are fixed.In particular, the 3D Cartesian coordinates of the BS, Eve, and RIS were chosen as [0, 0, 10], [10, 25, 1.5], and [10,55,5] in metres, respectively.Then, for each position of the legitimate RX on the map, the secrecy rate maximisation problem was solved based on the design in [49,50], where the linear precoding and the artificial noise covariance matrix at the BS, the linear combining matrix at RX, and the RIS passive beamforming vector, as well as the number of the transmitted streams are optimised either for perfect or imperfect knowledge of Eve's CSI.In this figure's results, the BS was assumed equipped with 8 antennas, Eve and RX share had both 4 antenna elements, and the RIS consisted of 400 unit cells.
Figure 21b is derived from Fig. 21a by applying a minimum SSE threshold criterion, whose value was set equal to 26 bits/sec/Hz.In locations where the SSE of Fig. 21a is below this predefined threshold, the network is incapable to serve the UE (as it cannot guarantee the minimum target SSE), thus, the UE is out of coverage the SSE was set to zero in Fig. 21b.Again, there exist three heatmaps of SSE in this figure: (i) without RIS; (ii) with RIS; and (iii) the difference due to the introduction of RIS. Figure 21c is derived from the right subfigure of Fig. 21b and enables us to visualise three areas: an "enabled area" where the RX is served by the BS (with the guaranteed minimum SSE) thanks to the RIS deployment and proposed optimisation; a "boosted area" where the SSE of RX is boosted thanks to RIS; and an "unchanged area" RX remains out of the BS's coverage.In the case where the RIS is not deployed, we observe in Fig. 21a that, close to the BS (i.e. at the bottom left corner) the secrecy rate is larger, reaching its maximum values throughout the considered grid of RX positions.This behaviour is expected, since at these positions, Eve's channel matrix is more degraded than RX's.However, when RX is located away from the BS and specifically above Eve in the grid (i.e. when y RX > y Eve ), SSE decreases considerably, reaching its minimum value, which is equal to 16.69 bits/ sec/Hz.On the other hand, when the RIS is deployed at the described position, it can be observed from the middle subfigure in Fig. 21a that the upper subarea (i.e. for y RX > y Eve ) gets boosted in terms of SSE performance.Particularly, the SSE increases approximately at least 2 bits/sec/Hz close to Eve's position and at least 10 bits/sec/Hz to RIS's position.The performance fluctuation of these two cases is better shown in the right subfigure Fig. 21a, where the difference between the latter two cases has been evaluated.In addition, it is observed that the maximum SSE difference, which is equal to 12.58 bits/sec/Hz, is attained close to the position where the RIS is located, while for the subarea close to the BS, the performance remains unchanged.In Fig. 21c, the SSE-optimised AoI is demonstrated, including areas where the targeted metric is either enabled or boosted, or remains unchanged.

Conclusions
In this paper, we elaborated on various deployment scenarios for RIS-enabled smart wireless environments, which were grouped in terms of performance objectives, namely connectivity and reliability, localisation and sensing, as well as sustainability and secrecy.The presented RIS-empowered scenarios are intended to offer substantial performance improvements in energy efficient manners, compared to conventional network deployments that lack RISs.We also presented a network architecture integrating RISs, which is compliant with already standardised interfaces, as they have been recently identified by the ongoing EU H2020 RISE-6G project.In particular, we devised an integration scheme of two RISs in a 3GPP network and discussed how RIS-oriented network entities can interact with O-RAN and ETSI interfaces.However, similar to any promising new technology, it was speculated that the increased potential of RISs is accompanied with certain challenges.
Two novel challenges with RISs were presented in this paper: the BoI and the AoI.The former describes the frequency bands that an RIS can impact, indicating the spectrum of the impinging signals whose reflection, and hence propagation, can be dynamically manipulated.The latter refers to the area around the RIS within which the propagation of signals with spectrum falling under the RIS BoI can be programmed on the fly via the metasurface's reconfigurability.We introduced mathematical definitions for the BoI's and the AoI's quantification and presented preliminary BoI measurements for four different unit cell implementations in different frequency bands (1-bit transmissive RIS at 27.3 GHz, varactor-based transmissive RIS at 5.8 GHz, RF-switch-based R-RIS at 5.3 GHz, and PIN-diode-based R-RIS at 5.05 GHz) and AoI simulations results for different performance metrics (EE/S-EMFEU, SE, and SSE).For the BoI challenge, it was showcased that it depends on the considered RIS unit cell technology, indicating that a careful consideration is necessary in practice especially when RISs are intended for multi-operator deployment cases.On the other hand, it was demonstrated that the AoI depends on the RIS hardware design and placement, the geometry of the deployment scenario, as well as the power level of the impinging signals, and it can be dynamically optimised to meet certain performance objectives, leading to notable improvements, independently of the adopted design criteria.
(a) Connectivity and reliability boosted by a single RIS.(b) RIS-empowered downlink communications of two BS-UE pairs, where each RIS can be controlled individually by each pair.

Fig. 1
Fig. 1 Illustration of the connectivity and reliability scenarios 2.1.1 and 2.1.2 (a) RIS-aided systems where connectivity is enabled by multiple RISs.(b)A multi-tenancy scenario with two BS-UE pairs and a shared RIS that is optimised to simultaneously boost reliable communications.

Fig. 2
Fig. 2 Illustration of the connectivity and reliability scenarios 2.1.3and 2.1.4

Fig. 6
Fig.6 An example integration scheme of two RISs in a 3GPP network, including a general interface among the different radio access network (RAN) entities.Each RIS panel is assumed to be managed by a dedicated controller that includes a transmitter (TX) and a receiver (RX) modules for exchanging Layer 1 (L1) and Layer 2 (L2) in-band signalling

Fig. 8
Fig. 8 Schematic definition of the maximum contrast and the BoI of a unit cell of an RIS

Fig. 11
Fig.11Channel state information mismatch due to time-varying undesired reflections from an RIS with a BoI and an AoI overlapping with the spectrum and coverage, respectively, of an unintended network operator

Fig. 12
Fig. 12 PIN-diode-based T-RIS unit cell characterisation: a structure, b states 000 and 180 and the c magnitude and d phase of their S11 and S21 parameter, and e contrast of the S-parameters for these states as a function of the frequency in GHz

Fig. 13
Fig. 13 Varactor-based R-RIS unit cell characterisation: a operation principle, b magnitude and c phase of the S11 parameter for various capacitances, and d contrast of the S11 parameter for various capacitance values versus the frequency in GHz

Fig. 14
Fig. 14 RF-switch-based R-RIS unit cell characterisation: a structure, b magnitude and c phase of the S11 parameter for the 7 different configurations, and d contrast of the S11 parameter for the considered different configurations versus the frequency in GHz

Fig. 15
Fig. 15 PIN-diode-based R-RIS unit cell characterisation: a structure, b magnitude and c phase of the S11 parameter for states 000 and 180, and d contrast of the S11 parameter for these states as a function of the frequency in GHz

Fig. 16
Fig. 16 Normalised BoI for the different fabricated RIS unit cells

Fig. 17
Fig.17 The simulated scenario for different UE positions, aiming at the EE/S-EMFEU AoI characterisation.The coverage inside and outside the building is analysed to unveil the influence of the RIS deployment.It is showcased that deploying a reflective RIS in the south leads to improvements in terms of achieving higher channel gains within this room

Fig. 21
Fig.21 The RIS AoI for the SSE performance metric considering the presence of an eavesdropper (Eve) by: a not applying and SSE threshold, b imposing the SSE threshold of 26 bits/sec/Hz, and c illustrating the resulting SSE-optimised AoI